Installation Instructions

Faz-Fit Fairway Woods & Hybrids

Shafts

  • Standard tip trim

    1.25” plus OEM recommended trim (allow 1.5” parallel section)

  • Shaft Preparation

    1. Abrade shaft tip 0.75” (remove all paint from tip section)
    2. Clean abraded shaft tip (acetone recommended)
  • Adapter Preparation

    1. Abrade inside of Faz-Fit Shaft Adapter
    2. Clean inside (cotton swab and acetone recommended)
  • Installation

    1. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    2. Fully coat inside of adapter and outside of shaft tip with epoxy
    3. Insert shaft into adapter (NOTE: shafting beads may be needed for better fit)
    4. Rotate to desired position (Default: shaft logo aligned with “dot(s)” on adapter)
    5. Tamp until shaft tip reaches full depth of adapter
    6. Wipe off excess epoxy on outside of shaft and adapter
    7. Allow epoxy to fully cure before handling again
  • Finishing

    1. Fairway Wood - butt trim to desired length (w/o head)
      1. Butt trim to 41” (w/o head) = 43” (total length w/ head)
      2. Convert length appropriately (e.g. 40.5” = 42.5”, etc.)
    2. Hybrid - butt trim to desired length (w/o head)
      1. Butt trim to 38” (w/o head) = 40.25” (total length w/ head)
      2. Convert length appropriately (e.g. 37.25” = 39.5”, etc.)
    3. Affix head to shaft, then measure CPM (no grip; 5” clamp at 40 psi)
    4. Install grip to desired position (Default: align grip logo with shaft logo)
    5. Label shaft with length and CPM (Default: 0.5” below grip, opposite of logos)

Shafts

  • Standard tip trim

    1.25” plus OEM recommended trim (allow 1.5” parallel section)

  • Shaft Preparation

    1. Abrade shaft tip 0.75” (remove all paint from tip section)
    2. Clean abraded shaft tip (acetone recommended)
  • Adapter Preparation

    1. Abrade inside of Faz-Fit Shaft Adapter
    2. Clean inside (cotton swab and acetone recommended)
  • Installation

    1. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    2. Fully coat inside of adapter and outside of shaft tip with epoxy
    3. Insert shaft into adapter (NOTE: shafting beads may be needed for better fit)
    4. Rotate to desired position (Default: shaft logo aligned with “dot(s)” on adapter)
    5. Tamp until shaft tip reaches full depth of adapter
    6. Wipe off excess epoxy on outside of shaft and adapter
    7. Allow epoxy to fully cure before handling again
  • Finishing

    1. Fairway Wood - butt trim to desired length (w/o head)
      1. Butt trim to 41” (w/o head) = 43” (total length w/ head)
      2. Convert length appropriately (e.g. 40.5” = 42.5”, etc.)
    2. Hybrid - butt trim to desired length (w/o head)
      1. Butt trim to 38” (w/o head) = 40.25” (total length w/ head)
      2. Convert length appropriately (e.g. 37.25” = 39.5”, etc.)
    3. Affix head to shaft, then measure CPM (no grip; 5” clamp at 40 psi)
    4. Install grip to desired position (Default: align grip logo with shaft logo)
    5. Label shaft with length and CPM (Default: 0.5” below grip, opposite of logos)

Heads

Must reference previously built shaft w/ Faz-Fit

  • Alteration

    Head weight with all Faz-Fit components should equal OEM weight

    1. Record OEM weight of head (w/ OEM adjustable adapter if applicable)
    2. Remove OEM ferrule (if applicable)
    3. Dry fit Faz-Fit Hosel Adapter w/ Nut into hosel
    4. Affix dry fitted head to shaft (previously built w/ Faz-Fit)
    5. Measure total length
    6. Measure the difference of labeled shaft length to actual club length
    7. Cut the difference in length from the hosel (if possible)
    8. Record weight of head, Faz-Fit Shaft & Hosel Adapter w/ Nut
    9. Add or relieve weight (if possible) to match original OEM weight
  • Installation

    Bonding Faz-Fit Hosel Adapter w/ Nut and head

    1. Abrade inside of hosel
    2. Abrade Faz-Fit Hosel Adapter
    3. Clean all abraded surfaces (acetone recommended)
    4. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    5. Fully apply a light coat of epoxy inside the hosel
    6. Feed Hosel Adapter through Nut
    7. Insert Faz-Fit Hosel Ad. Install Tool into Hosel Adapter
    8. Carefully apply epoxy to the portion of Hosel Adapter that inserts the hosel
    9. Insert fully into hosel
    10. Align indicator line on Faz-Fit Hosel Ad. Install Tool parallel to club face
    11. Wipe excess epoxy (NO NOT LEAVE EPOXY ON ANY THREADINGS)
    12. Remove Install Tool
    13. Allow epoxy to fully cure before handling again
Back to Faz-Fit product knowledge

Heads

Must reference previously built shaft w/ Faz-Fit

  • Alteration

    Head weight with all Faz-Fit components should equal OEM weight

    1. Record OEM weight of head (w/ OEM adjustable adapter if applicable)
    2. Remove OEM ferrule (if applicable)
    3. Dry fit Faz-Fit Hosel Adapter w/ Nut into hosel
    4. Affix dry fitted head to shaft (previously built w/ Faz-Fit)
    5. Measure total length
    6. Measure the difference of labeled shaft length to actual club length
    7. Cut the difference in length from the hosel (if possible)
    8. Record weight of head, Faz-Fit Shaft & Hosel Adapter w/ Nut
    9. Add or relieve weight (if possible) to match original OEM weight
  • Installation

    Bonding Faz-Fit Hosel Adapter w/ Nut and head

    1. Abrade inside of hosel
    2. Abrade Faz-Fit Hosel Adapter
    3. Clean all abraded surfaces (acetone recommended)
    4. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    5. Fully apply a light coat of epoxy inside the hosel
    6. Feed Hosel Adapter through Nut
    7. Insert Faz-Fit Hosel Ad. Install Tool into Hosel Adapter
    8. Carefully apply epoxy to the portion of Hosel Adapter that inserts the hosel
    9. Insert fully into hosel
    10. Align indicator line on Faz-Fit Hosel Ad. Install Tool parallel to club face
    11. Wipe excess epoxy (NO NOT LEAVE EPOXY ON ANY THREADINGS)
    12. Remove Install Tool
    13. Allow epoxy to fully cure before handling again
Back to Faz-Fit product knowledge