Installation Instructions

Uni-Fit Drivers

Shafts

  • Standard tip trim

    0” (custom trim may be achieved; allow 1.5” parallel)

  • Shaft Preparation

    1. Abrade shaft tip 0.75” (remove all paint from tip section)
    2. Clean abraded shaft tip (acetone recommended)
  • Adapter Preparation

    1. Abrade inside of Uni-Fit Shaft Adapter (until black is removed from inside)
    2. Clean inside (cotton swab and acetone recommended)
  • Installation

    1. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    2. Fully coat inside of adapter and outside of shaft tip with epoxy
    3. Insert shaft into adapter (NOTE: shafting beads may be needed for better fit)
    4. Rotate to desired position (Default: shaft logo aligned with “Neutral”)
    5. Tamp until shaft tip reaches full depth of adapter
    6. Wipe off excess epoxy on outside of shaft and adapter
    7. Allow epoxy to fully cure before handling again
  • Finishing

    1. Butt trim to length
      1. Butt trim to 43” (no head) for STD length (45”)
      2. Convert appropriately for different lengths (e.g. 42.5” = 44.5”, etc.)
    2. Affix head to shaft, then measure CPM (no grip; 5” clamp at 40 psi)
    3. Install grip to desired position (Default: align grip logo with shaft logo)
    4. Label shaft with length and CPM (Default: 0.5” below grip, opposite of logos)

Shafts

  • Standard tip trim

    0” (custom trim may be achieved; allow 1.5” parallel)

  • Shaft Preparation

    1. Abrade shaft tip 0.75” (remove all paint from tip section)
    2. Clean abraded shaft tip (acetone recommended)
  • Adapter Preparation

    1. Abrade inside of Uni-Fit Shaft Adapter (until black is removed from inside)
    2. Clean inside (cotton swab and acetone recommended)
  • Installation

    1. Fully mix 2-part epoxy (golf club specific - other epoxies NOT recommended)
    2. Fully coat inside of adapter and outside of shaft tip with epoxy
    3. Insert shaft into adapter (NOTE: shafting beads may be needed for better fit)
    4. Rotate to desired position (Default: shaft logo aligned with “Neutral”)
    5. Tamp until shaft tip reaches full depth of adapter
    6. Wipe off excess epoxy on outside of shaft and adapter
    7. Allow epoxy to fully cure before handling again
  • Finishing

    1. Butt trim to length
      1. Butt trim to 43” (no head) for STD length (45”)
      2. Convert appropriately for different lengths (e.g. 42.5” = 44.5”, etc.)
    2. Affix head to shaft, then measure CPM (no grip; 5” clamp at 40 psi)
    3. Install grip to desired position (Default: align grip logo with shaft logo)
    4. Label shaft with length and CPM (Default: 0.5” below grip, opposite of logos)

Heads

  • Alteration

    Head weight with all Uni-Fit components should equal OEM weight

    1. Record OEM weight of head w/ OEM adjustable adapter (save for later)
    2. Remove OEM adjustable adapter
    3. Record total weight of head, Uni-Fit Shaft Adapter, and Uni-Fit Hosel Adapter
    4. Add or relieve weight (if possible) to match original OEM weight
  • Installation

    1. Match appropriate Uni-Fit Hosel Adapter to vendor head
    2. Align desired setting of Uni-Fit Shaft Adapter with dot(s) on Hosel Adapter
    3. Align shaft adapter and hosel adapter dot(s) with driver head
    4. Tighten color-coded bolt with Torque Wrench until audible “click” is achieved
Back to Uni-Fit product knowledge

Heads

  • Alteration

    Head weight with all Uni-Fit components should equal OEM weight

    1. Record OEM weight of head w/ OEM adjustable adapter (save for later)
    2. Remove OEM adjustable adapter
    3. Record total weight of head, Uni-Fit Shaft Adapter, and Uni-Fit Hosel Adapter
    4. Add or relieve weight (if possible) to match original OEM weight
  • Installation

    1. Match appropriate Uni-Fit Hosel Adapter to vendor head
    2. Align desired setting of Uni-Fit Shaft Adapter with dot(s) on Hosel Adapter
    3. Align shaft adapter and hosel adapter dot(s) with driver head
    4. Tighten color-coded bolt with Torque Wrench until audible “click” is achieved
Back to Uni-Fit product knowledge